Oreck FC1000 Manual do Utilizador

Quest Pro CanisterFC1000Important!Read this manual carefully, and keep for future reference.User’s Guide®

7UseConnect Hose• With hose toward rear of the vacuum, push hose connector into opening in the bag lid. Note: The exible hose contains electric

8UseDirt Sensor • The Dirt Sensor will turn red (J) when the power nozzle is detecting and picking up dirt. The light will turn green when no dirt i

9• To set the power nozzle for hard surfaces, push the oor surface selector switch to “OFF” (L). This setting provides suction and no brushroll act

10Cleaning Tools• The cleaning tools are conveniently stored in the vacuum underneath the tool lid (P). Push the tool lid release latch to open (Q).

11Attaching Tools• Tools may be attached directly to the handle or to the wand. Firmly push tool onto the handle or wand. Twist tool slightly to tig

12WARNING!!Maintenance• Performing maintenance on the vacuum while it is plugged into a wall outlet may result in unexpected vacuum operation, shock

13Filter Bag• Check the lter bag when the bag full indicator light turns red.• When the lter bag is lled with dirt, the vacuum will not operate e

14Install New Bag • Slide the bag collar rmly into bag dock.Complete the Installation • Push rear edge of bag into the bag cavity. Make sure it i

15• Wash lter in warm water or replace it with a new one. The lter must be completely dry before it is put back into the vacuum. DO NOT operate

16Remove Nozzle Hood• Turn the nozzle upright and lift the hood off (B). Remove Brushroll Cover• Remove brushroll cover (C) by removing the 2 phil

Other Oreck accessories available at:Other Oreck accessories available at:Other Oreck accessories available at:Thank You for purchasing an Oreck Quest

17Check/Remove Belt• If belt is not broken but is stretched or cut, pull it off the motor pulley (D).Remove/Replace Belt• Lift up the end of the b

18Replace Brushroll Cover• Place brushroll cover back over the brushroll. • Replace the two cover screws.Replace Nozzle Hood• The wand must be i

19How to Replace the Brushroll DISCONNECT VACUUM FROM ELECTRICAL OUTLET!1. Remove hood, brushroll cover, belt and brushroll. See Steps 1-6.2. Discard

20• If there is no blockage in the hose. Remove the power nozzle from wand and attach wand to hose. Check for suction and remove any blockages.Nozzl

21Problem Check SolutionVacuum does not turn ON.• Power Cord • Power Source • Hose Connection• Thermal Protector• Plug in Power Cord. Make sure i

22WarrantyORECK MANUFACTURING COMPANY: (Oreck Manufac-turing Company gives you the following limited warranty for this product only if it was original

23

24

25©2010 Oreck Holdings, LLC. All rights reserved. All marks, text, logo’s, product con-gurations and registered trademarks are owned and used under

ContentsSafety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 General Warnings . . . . . . . . . . . . . . . . . . . . . . .

1SafetyIMPORTANT SAFETY INSTRUCTIONS!General Warnings Read all instructions before using this vacuum cleanerWhen using an electrical appliance, basic

2Note: A polarized plug has one rounded prong and one straight prong. The rounded end goes into the longest socket slot.• A damaged cord or plug ma

3an enclosed space. Always check exposed wiring and wire connections before use.• Vacuuming burning or smoking objects, ammable or combustible liqui

4Parts16. Bag Dock17. Motor Filter Grill18. Motor Filter19. Hepa Media Filter20. Crevice Tool21. Combination Tool22. Tool Lid Latch23. Bag Lid

5Assembling the Oreck Quest™ Pro Canister1. Connect hose by rmly inserting end of hose into canister intake opening.2. Firmly press handle nozzle i

6UseON/OFF Switch • After assembling vacuum, plug the cord into an electrical outlet. Turn the vacuum ON by pressing the ON/OFF pedal (A). To turn v